ROAD REPAIR MACHINES

More than 650 machines are already in service around the world.
The machines are highly productive with minimal waste material

JETPATCHER Advantages

We use an innovative Jet Distributor

Jetpatcher™ Road Repair Machinery will repair potholes and road surfaces.

 

 

Crewing

JETPATCHER requires only a crew of two, plus additional traffic control assistance if necessary. In a situation for repairs to car parks, shopping center parking lots and areas where traffic may be lesser, a crew of one is sufficient assuming that local Health and Safety regulations allow.

Clean-up and Preparations

After use, flush out the delivery hose and nozzle with water, and hose down the machine. Leave the spray ring from the nozzle soaking overnight in kerosene. Fill up with aggregate, emulsion and water, and plug in the overnight heater. In the morning, unplug the heater, re-assemble the nozzle, and drive away.

At the end of the week, or before an extended period of non-use, use the inbuilt facility to flush the emulsion lines and nozzle with water.

Self-contained Resource

JETPATCHER is a fully self-contained unit that cleans, compacts, fills and seals the repair area – no other vehicles are required for support other than standard traffic management and local requirements for repair operations.

High Productivity

High productivity is available from the JETPATCHER crew, typically 7 tons per day, with much lower physical effort than required for traditional methods. The job of driver/traffic controller could easily be done by either male or female members of staff.

High productivity from the JETPATCHER crew with much lower physical effort than that required for traditional methods of repair means job satisfaction is enhanced resulting in better labour retention and work skill development.

Longer Life of Repairs

Longer lasting repairs are achieved than from using traditional methods because the JETPATCHER material is always fresh and sets almost immediately. Single layer compaction from the base of the pothole up from the high-velocity jet stream gives superior compaction.

There is not the tendency of the JETPATCHER material to creep back from the edges of the repair over time as can occur with hot mix and cold mix.

The Jetpatcher™ provides a cost-effective way of maintaining the wearing surfaces of asphalt roads, car parks, footpaths and industrial areas including repairs of potholes, crack seals, scabbing, depressions, utility cuts, shoulder repairs, alligator cracking and wheel path rutting repairs.

Jetpatcher™ is the only machinery that utilizes a specialized distributor system which allows Jetpatcher™ to provide high production rates with little wear as there are no moving parts.  This eliminates costly time and maintenance costs for the operators.

Jetpatcher™ road maintenance units are based on front or rear truck mounted units or trailer units. These units are customized with a selection of optional equipment to cover required tasks.

The Jetpatcher™ Road Repair machines come in a range or sizes from 2 to 8 cubic meter capacity. When considering Jetpatcher machines make sure you are aware of all the options available. We are always available to discuss what is most suitable for your particular situation.

Series 1000

Trailer Mounted Unit

The series 1000 trailer unit is perfect for around town use; it can be towed behind a truck and is completely self-contained.

They have the same output as the larger units with no compromise as to the working of the machine and the delivery system.

The standard 1000 trailer series units comprise of –

  • Mudguards
  • Full-length rear step
  • Retractable water hose
  • Camera with LCD monitor
  • 60 Liter fuel tank capacity
  • Water line cleaning system
  • LED directional traffic safety light
  • 200 Liter emulsion drum pressure fill
  • Kerosene injection for cleaning of nozzle
  • Air Relief valve for operators instant control
  • 110V / 220V overnight emulsion heating system
  • Separate water injection for aggregate line cleaning
  • Gas stay Variable Height Adjustor for operators control
  • Soaker box for self-cleaning of filters, spray rings and nozzle

Follow this link (open in new tab) to download our brochure on the Series 1000 Trailer Mountable Unit

Series 1000

Truck Mounted Unit

The series 1000 unit is a completely self-sufficient unit with a 2.5m3 to 5m3 capacity. The 1000- 2.5Cum – 5Cum unit is a truck mountable unit. Though the 2.5Cum only can be fitted to a trailer as a trailer unit.

These smaller, economical units are ideal for urban and suburban work. They have the same output as the larger units with no compromise as to the working of the machine and the delivery system.

The standard 1000 series units comprise of –

  • Aggregate storage hopper with optional capacities of 2.5m3 to 5m3
  • Emulsion tank storage nominal 750L (2.5Cum unit) – 1500L (5Cum unit)
  • High volume air blower for aggregate flow
  • Air compressor to pressurise emulsion, water and kerosene tanks
  • Pressurised tanks for water and kerosene for cleaning, dampening dry aggregate, purging emulsion lines and spraying
  • Easily accessible controls
  • Patented aggregate feed system
  • Auxiliary engine
  • Placement boom / delivery hose with jet distributor unit
  • Low noise enclosures and air flow silencing
  • Standard units are complete with sign rack, tool box, rear step, mudguards, retractable water hose, pressure drum fill
  • All units use the jet delivery system with no moving parts and minimal maintenance. Delivery rate for each type of unit is a minimum of 2.5m³ per hour.

Follow this link (open in new tab) to download our brochure on the Series 1000 Truck Mountable Unit as well as the Recommended Truck Specifications Brochure

Series 2500

Truck Mounted Unit

Truck mounted units, 4 to 8 cubic meter capacity with conveyor and hydraulics.

The series 2500 units are designed to be installed on truck cab/chassis as an entirely self-sufficient unit.

These truck mounted units are manoeuvrable and suited to both urban and country areas. The larger hopper capacity allows increased aggregate load to be carried.

The standard 2500 series units comprise of –

  • Aggregate storage hopper with optional capacities of 4m3 to 8m3
  • Full-length conveyor discharge – hydraulic powered
  • Emulsion tank storage from a nominal 600 litres to 2000 litres to suit hopper capacity
  • High volume air blower for aggregate flow
  • Air compressor to pressurize emulsion, water and kerosene tanks
  • Pressurized tanks for water and kerosene for cleaning, dampening dry aggregate, purging emulsion lines and spraying
  • Easily accessible controls
  • Patented aggregate feed system
  • Auxiliary engine
  • Placement boom / delivery hose with swivelling jet distributor unit
  • Low noise enclosures and air flow silencing
  • Standard units are complete with sign rack, toolbox, rear step, mudguards, ladder, retractable water hose, pressure drum fill

Follow this link (open in new tab) to download our brochure on the Series 2500 Truck Mountable Unit as well as the Recommended Truck Specifications Brochure

Standard & Optional Extra Components

Standard components for a Jetpatcher™ unit include –

  • Hopper
  • Emulsion tank
  • 110/220 Volt overnight heating
  • Pressurised tanks for water and kerosene for cleaning, dampening dry aggregate, purging emulsion lines and spraying
  • High volume air blower for aggregate flow
  • Easily accessible controls
  • Patented aggregate feed system
  • Remote camera with LCD monitor
  • Auxiliary engine
  • Placement boom / delivery hose with jet distributor unit
  • Low noise enclosures and air flow silencing
  • Standard units complete with sign rack, tool box, rear step, mudguards & directional safety arrow

 

Optional extra components for a Jetpatcher™ unit include –

  • Split hopper for sand (larger hoppers only)
  • Spreader box (for the 2500 series units only)
  • Front mounted delivery system
  • Remote hydraulic outlet for hydraulic tools
  • Compactor with transport tray fitted
  • Sand hopper filler bin – for ease of filling sand hopper (if fitted)
  • Services of a commissioning engineer

Need to know more?

Our Workshop

Our Sales Partner

Jetpatcher Canada Sales
Phone - 306.227.3554
Email - sales@jetpatcher.ca